RF & Microwave PCB

Advanced RF and microwave PCB solutions with ultra-low loss materials for optimal signal integrity.

PIM performance ≤ −159 dBc for phased array and antenna applications. 40+ years heritage since 1982,

24+ years RF/microwave expertise since 2000. Tested to 77GHz for automotive radar and mmWave applications.

Current Location: Home > Solutions > RF & Microwave PCB

RF & Microwave PCB

Product Features

Low-Loss Material Options – PTFE, ceramic-filled, hydrocarbon, low-loss, and high-frequency material systems available by project review
Wide Material Selection – Support for high-frequency materials with different Dk and Df ranges based on design requirements
Controlled Impedance – Typical impedance tolerance from ±7% to ±10%, with tighter requirements available by engineering review
RF & Microwave Support – Stack-up and material support for RF, antenna, radar, and microwave applications up to 40 GHz class by project review
Precision Fabrication – Fine line control, mixed dielectric stack-ups, controlled depth routing, back drilling, and surface finish options for RF designs

Basic Information

Layer Count
2-layer to multilayer high-frequency PCB; high-layer mixed dielectric structures by project review
Board Thickness
0.127 mm – 5.0 mm, depending on material and stack-up
Max Board Size
Up to 570 mm x 500 mm for precision high-frequency projects; larger sizes by review
Min Line Width / Spacing
Down to 35/35 um for advanced products; design-dependent
Min Mechanical Drill
Down to 0.10 mm for advanced structures
Min Laser Drill
Available by project review
Copper Weight
Standard 1/3 oz – 5 oz; heavy copper up to 12 oz inner / 14 oz outer by project review
Impedance Tolerance
±8% typical; tighter requirements by project review
Frequency Range
RF and microwave applications up to 40 GHz class by material and stack-up review
Materials
PTFE, ceramic-filled, hydrocarbon, PPO/PPE, modified epoxy, low-loss, high-speed, High Tg FR-4, Aegis, Rogers, Arlon, AGC, Shengyi, Panasonic, Isola, ITEQ

RF & Microwave Material Selection

Why Material Selection Matters: At higher frequencies, signal loss increases dramatically due to dielectric absorption, conductor roughness, and surface finish effects. Choosing the wrong material can cost you dB of signal loss and failed designs. We manufacture our own PTFE and ceramic laminates, giving you direct access to ultra-low loss materials without middleman markup.

What We Provide & Our Material Portfolio

→Complete Dk/Df Data — Tested at 10GHz, 40GHz, and 77GHz for your frequency band
→Material Sample Kit — Physical samples for dielectric testing and evaluation
→Hybrid Stack-up Design — Optimize cost with PTFE for RF layers, FR4 for digital
→Impedance Modeling — Precise calculations based on actual material properties
→Surface Finish Guidance — ENIG, ENEPIG, or immersion tin recommendations
RF & Microwave Material Comparison
AEGIS PCB high-frequency laminates — industry-standard alternatives for demanding applications
AEGIS PCB advantage: Direct-from-manufacturer high-frequency laminates with ultra-low dissipation factors. AG-RF-507 Series offers Df as low as 0.0010 (pure PTFE + ceramic, no glass fiber). AG-RF-505 Series provides ASTM E595 specimens qualified for material qualification tests at 77–110GHz.
MaterialManufacturerMaterial TypeDk @ 10 GHzDf @ 10 GHzApplications
AG-RF-507 SERIES — PTFE + CERAMIC (NO GLASS FIBER)
AG-RF-507-234AEGIS PCBIN-STOCKSAMPLE AVAILABLEPure PTFE + Ceramic (no glass fiber)2.940.0010Phased array antennas, early warning radar, satellite navigation
RO3002ROGERSCeramic-filled PTFE2.940.0012Phased array antennas, radar systems
AG-RF-507-300AEGIS PCBIN-STOCKSAMPLE AVAILABLEPure PTFE + Ceramic (no glass fiber)3.000.001077GHz automotive radar, mmWave 5G, T/R modules
RO3003ROGERSCeramic-filled PTFE3.000.0010Automotive radar, mmWave 5G, T/R modules
AG-RF-507-415AEGIS PCBIN-STOCKSAMPLE AVAILABLEPure PTFE + Ceramic (no glass fiber)6.150.0015mmWave beam networks, phased arrays, missile T/R modules
RO4350BROGERSCeramic-filled PTFE6.150.0022Patch antenna arrays, mmWave phased-array antennas
AG-RF-507-200AEGIS PCBIN-STOCKSAMPLE AVAILABLEPure PTFE + Ceramic (no glass fiber)10.20.0015Phased array antennas, dielectric resonator antennas, satellite navigation
RO3010ROGERSCeramic-filled PTFE10.20.0025Antenna miniaturization, satellite electronics, GPS antennas
AG-RF-505 SERIES — SPACE-GRADE PTFE (ASTM E595 QUALIFIED)
AG-RF-505-220AEGIS PCBIN-STOCKSAMPLE AVAILABLESpace-grade PTFE + Ceramic + Glass (ASTM E595)2.200.0009LEO satellites, space-qualified systems, satellite communication
TLX-9TACONICPTFE + Ceramic + Glass2.200.0009Aerospace, military radar, satellite transceivers
CuClad 217ROGERSPTFE + Ceramic2.170.0009Space, military radar
AG-RF-505-254AEGIS PCBIN-STOCKSAMPLE AVAILABLESpace-grade PTFE + Ceramic + Glass (ASTM E595)2.940.0010LEO satellites, aerospace radar, satellite communication
CLTE-XTROGERSPTFE + Ceramic2.940.0010Space, Aerospace, radar
AG-RF-505-300AEGIS PCBIN-STOCKSAMPLE AVAILABLESpace-grade PTFE + Ceramic + Glass (ASTM E595)3.000.0013LEO satellites, space antennas
CLTEROGERSPTFE + Ceramic3.000.0028Space antennas, mmWave
AG-RF-505-350AEGIS PCBIN-STOCKSAMPLE AVAILABLESpace-grade PTFE + Ceramic + Glass (ASTM E595)3.500.0015LEO satellites, aerospace systems
AD350TACONICCeramic-filled PTFE3.500.0030Aerospace, military
AG-RF-505-615AEGIS PCBIN-STOCKSAMPLE AVAILABLESpace-grade PTFE + Ceramic + Glass (ASTM E595)6.150.0020LEO satellites, phased array antennas
AD600TACONICCeramic-filled PTFE6.150.0024Phased arrays, aerospace
AG-RF-503 SERIES — ULTRA-LOW LOSS PTFE
AG-RF-503-220AEGIS PCBIN-STOCKSAMPLE AVAILABLEPTFE + Ceramic + Glass (short fiber)2.200.00085G mmWave, phased array antennas, base stations
RT/duroid 5880ROGERSPTFE + Glass2.200.0009Microwave antennas, radar
AG-RF-508 SERIES — HYDROCARBON CERAMIC (COST-EFFECTIVE)
AG-RF-508-338AEGIS PCBIN-STOCKSAMPLE AVAILABLEHydrocarbon + Ceramic + Glass3.380.00285G base station antennas, radar sensors, power amplifiers
RO4003CROGERSHydrocarbon + Ceramic3.380.00275G base stations, RF power amplifiers, radar
AG-RF-508-350AEGIS PCBIN-STOCKSAMPLE AVAILABLEHydrocarbon + Ceramic + Glass3.480.004024GHz automotive radar, commercial RF, satellite LNB
RO4003BROGERSHydrocarbon + Ceramic3.480.003724GHz automotive radar, commercial RF, satellite modems
AG-RF-508-300AEGIS PCBIN-STOCKSAMPLE AVAILABLEHydrocarbon + Ceramic + Glass3.000.0017High-speed digital, RF/microwave, automotive radar
RO3003ROGERSCeramic-filled hydrocarbon3.000.0010High-speed digital, RF
Astra MT77ISOLAEpoxy + Ceramic + Glass3.000.0017High-speed digital, backplanes, servers
I-Speed 4ISOLAEpoxy + Ceramic + Glass3.000.0037High-speed digital, networking, computing
FR408HRISOLAEpoxy + Ceramic + Glass3.300.00315G base stations, RF power amplifiers, automotive radar
370HRISOLAEpoxy + Ceramic + Glass4.100.0035High-speed digital, multilayer RF, automotive
Tera MT40ISOLAEpoxy + Ceramic + Glass5.000.00505G massive, high-speed digital, automotive
Key Takeaway: AEGIS PCB offers comprehensive high-frequency laminate solutions with four major series: AG-RF-507 Series (PTFE + ceramic, no glass fiber) for mmWave and radar, AG-RF-505 Series (ASTM E595 space-qualified) for LEO satellites and aerospace, AG-RF-503 Series (ultra-low loss, Df 0.0008) for 5G mmWave and phased arrays, and AG-RF-508 Series (hydrocarbon ceramic) for cost-effective 5G and automotive applications. All AEGIS materials are tested at 10GHz with VNA verification up to 77–110GHz, ASTM E595 certified for automotive ADAS.
Trademarks & Disclaimer: RO4003C, RO4350B, RO3003, RO3010, RT/duroid 5880, AD250C, AD350, AD600, TLX-9, CuClad 217, CLTE, CLTE-XT, Astra MT77, I-Speed 4, FR408HR, 370HR, Tera MT40 are trademarks of their respective owners, referenced for technical comparison purposes only. AEGIS PCB specifications are based on published datasheets and internal testing; actual performance may vary. Refer to official datasheets for detailed specifications.
AEGIS PCB  |  High-Frequency Laminates  |  77–110GHz Testing  |  ASTM E595 Certified
Orange highlight = AEGIS PCB materials    Dk: Dielectric constant (lower = faster signal speed)  |  Df: Lower value = lower signal loss
Space: AG-RF-505 Series ASTM E595 qualified (TML<1.0%%, CVCM<0.01%%)

Application Areas

5G mmWave & Base Stations

hased array antennas, base station RF boards, mmWave transceivers (24-40 GHz), PIM-sensitive applications (≤ −159 dBc), low-loss materials for minimal signal attenuation

Radar Systems

Automotive radar (77GHz), weather radar, air traffic control radar, marine navigation radar, surveillance systems (L-band to Ka-band, 1-40 GHz), phased array radar with ultra-low loss requirements

Satellite Communications

LEO satellite transceivers, ground station equipment, GPS/GNSS systems, satellite uplink/downlink (L, S, C, X, Ka bands), space-grade materials available (ASTM E595)

Antenna & PCB Antenna

Phased array antennas, patch antennas, microstrip antennas, antenna feed networks, directional arrays, antenna integration with RF circuitry

Test & Measurement Equipment

Vector network analyzer boards, RF test fixtures, microwave test equipment, high-frequency instrumentation boards, calibration standards

Aerospace & Defense RF

Electronic warfare systems, RF amplifiers, transmitters, signal intelligence systems, high-reliability RF subsystems, harsh environment deployment

RF & Microwave Manufacturing Capabilities

AEGIS PCB provides comprehensive RF and microwave PCB manufacturing with 24+ years of experience in high-frequency applications. Our facility supports the full product lifecycle from quick-turn prototypes to high-volume production runs with complete material lot traceability and advanced testing capabilities.

What Makes AEGIS Different for RF & Microwave PCBs

1
Project-specific testing and inspection for RF and microwave PCB requirements
2
TDR impedance testing available for controlled impedance boards
3
RF and microwave stack-up support up to 40 GHz class by material and design review
4
Additional RF testing can be arranged based on project requirements
5
X-ray inspection available for selected multilayer and via reliability requirements
6
AOI inspection for inner layers, trace/space verification, and defect detection
7
Material lot tracking and project documentation for traceability

Common RF & Microwave PCB Design Mistakes

Learn from real-world failures we’ve seen in 24+ years of manufacturing. Avoid these costly errors.

1

Glass Fiber Effect at Millimeter-Wave Frequencies

Problem: Standard woven-glass laminates cause anisotropic signal propagation (glass fiber effect) at extreme frequencies.

Impact: At 77GHz automotive radar, glass weave caused 3.2 dB higher insertion loss and phase instability in beam steering.

Root Cause: Glass fibers have different Dk than resin, creating discontinuities that scatter electromagnetic waves.

Solution: Use pure PTFE/ceramic composites (TFA series) or random short-glass fibers to eliminate glass weave effect.

Engineering Note: For frequencies above 30GHz, always specify glass-free materials or random-glass alternatives.
2

Standard HTE Copper at High Frequencies

Problem: Specifying standard HTE (High Temperature Elongation) copper foil with Rz 7-11μm surface roughness.

Impact: At 77GHz radar application, conductor loss increased by 1.8 dB/inch due to skin effect traveling along rough copper surface. PIM degraded to −150 dBc.

Root Cause: Rough copper surface exponentially increases conductor loss at high frequencies and creates micro-burrs that cause PIM.

Solution: Specify RTF (Reverse Treated Foil) or HVLP foils with Rz < 3.5μm for frequencies above 10GHz.

Engineering Note: Copper roughness becomes critical above 10GHz. Always specify RTF for mmWave and 5G applications.
3

Ignoring Adhesive-Backed Copper Foil Thickness

Problem: RTF copper foil uses 0.018mm (0.7mil) adhesive backing that increases dielectric thickness.

Impact: 50Ω controlled impedance board measured 58Ω actual due to uncompensated adhesive layer, causing VSWR 1.6:1 mismatch.

Root Cause: Impedance calculator failed to account for adhesive layer thickness in dielectric spacing.

Solution: Add 0.018mm compensation in impedance calculations when using RTF or adhesive-backed foils.

Engineering Note: Always verify with your fabricator whether adhesive-backed copper is used and adjust calculations accordingly.
4

Overly Tight Impedance Tolerances

Problem: Designer specified ±3% impedance tolerance for mass production.

Impact: 85% yield loss due to unachievable tolerance. Real-world mass production capability is ±10% standard or ±7% with extreme precision.

Root Cause: Designers unfamiliar with fabrication capabilities specify R&D-level tolerances for production.

Solution: Use ±10% for production, ±7% only for critical applications with statistical process control.

Engineering Note: Consult with your fabricator before specifying impedance tolerances tighter than ±7%.

Real-World RF & Microwave PCB Projects

Real projects delivered. See how RF and microwave PCBs enabled cutting-edge applications.

📡

5G mmWave Phased Array

Specs: 28GHz, 256 elements, PTFE (Dk 2.20, Df 0.0008), PIM ≤−159 dBc

Challenge: Ultra-low loss required for 28GHz phased array with stringent PIM requirements.

Solution: Ultra-low loss PTFE + RTF copper + hybrid stackup (PTFE RF + FR4 digital) + 100% TDR + PIM testing.

Results: 0.42 dB/inch @ 28GHz · −162 dBc PIM · 98.5% yield.

🚗

77GHz Automotive Radar

Specs: 77GHz, ceramic-filled PTFE, −40°C to +125°C, AEC-Q100 qualified

Challenge: Extreme temperature range with Dk stability <±3% and <1.0 dB/inch insertion loss @ 77GHz.

Solution: Temperature-stable ceramic PTFE + VLP copper + 77GHz VNA verification + AEC-Q100 protocol.

Results: 0.76 dB/inch @ 77GHz · ±1.5% Dk variation · 97.8% yield.

🛰️

Satellite Communication

Specs: Ka-band (35GHz), space-grade PTFE, ASTM E595 certified, TML <1.0%

Challenge: Ka-band satellite transceiver with outgassing compliance and radiation resistance required.

Solution: Space-grade PTFE (TML 0.8%, CVCM 0.08%) + 35GHz VNA verification + thermal vacuum testing.

Results: 0.48 dB/inch @ 35GHz · Passed thermal vacuum · LEO qualified.

Factory Audit & Site Verification

AEGIS PCB welcomes customer factory audits and third-party site verification at our ISO 9001-certified manufacturing facilities.

AEGIS RF & Microwave PCB - rfm-c350a519e9c9-8aa563

🏭

On-Site Audit & Support Services

  • Production floor tour — Witness PTFE lamination
  • Quality laboratory — Verify 77GHz VNA, TDR, PIM equipment
  • Material storage — Audit lot tracking
  • Dedicated audit coordinator assigned
  • Complete documentation package provided
  • Virtual factory tour via Zoom/Teams
📋

Schedule & Contact

  • Contact: quote@aegispcb.com
  • On-site audit: Full-day or half-day visit
  • Virtual tour: Live video inspection with Q&A
  • Pre-visit docs: Audit preparation package 5 days in advance
  • Translation support: Multi-language on-site interpretation available (including English)
  • Security note: Defense projects may require additional clearance

Ready to Schedule Your Factory Audit?

Contact us today for on-site visit or virtual tour.

Our RF & Microwave PCB Manufacturing & Testing Equipment

Advanced manufacturing and testing capabilities — from laser imaging and copper plating to 77GHz VNA and PIM verification.

AEGIS PCB solutions - sol-ef2f8ea10a5e-e6c126
LASER IMAGING
LDI Laser Direct Imaging
25μm fine line, solder mask & outer layer
AEGIS PCB solutions - sol-897686aaada9-2ea983
MECHANICAL DRILLING
Drilling Machine
0.15mm micro-via, ±0.05mm accuracy
AEGIS PCB solutions - sol-e96d97259a4d-95b13c
PTH & PLATING
Auto PTH & Copper Plating
Auto horizontal line, 25μm Cu thickness
AEGIS PCB solutions - sol-de29094a60b1-9b24d2
VACUUM ETCHING
DES Vacuum Etching
3mil trace etching, ±10% uniformity
AEGIS PCB solutions - sol-c156fe5d8a3b-215ed9
AUTOMATED OPTICAL
AOI System
Inner layer inspection before lamination
AEGIS PCB solutions - sol-c67ba1523f47-6531e4
X-RAY INSPECTION
X-Ray System
Layer registration, via formation verification
AEGIS PCB solutions - sol-a751bec9f658-9af86c
NETWORK ANALYZER
77GHz VNA
Insertion loss, return loss, S-parameters
AEGIS PCB solutions - sol-98794709d155-f59d32
IMPEDANCE TESTER
TDR Tester
100% controlled impedance verification
AEGIS PCB solutions - sol-02c6db3ce846-6576cd
PIM ANALYZER
PIM Tester
Passive intermodulation up to 2600MHz
AEGIS PCB solutions - sol-be4e1ecef55a-1b786c
ELECTRICAL TEST
Flying Probe
100% netlist verification
AEGIS PCB solutions - sol-762640c0ef1e-6f1b04
EMC/EMI CHAMBER
Microwave Anechoic Chamber
Antenna pattern, EMC/EMI, radiated emissions
AEGIS PCB solutions - sol-f4269ef9d9ed-b89d4d
METALLOGRAPHIC
Metallographic Microscope
Micro-section analysis, copper grain structure

Frequently Asked Questions

Expert answers to common questions about RF and microwave PCB materials, PIM performance, 

impedance control, and hybrid stackups.

 

RF (Radio Frequency) typically refers to frequencies from 300 kHz to 300 MHz, while Microwave covers 300 MHz to 300 GHz. In PCB manufacturing, the distinction matters because: 1. Material requirements: RF < 3 GHz can use high-quality FR-4. Microwave > 3 GHz requires PTFE/ceramic laminates with Df < 0.003. 2. Testing: RF boards tested to 1-3 GHz. Microwave boards tested to 10-77 GHz. 3. Design: Microwave requires tighter impedance control (±7% vs ±10%) and back-drilling. 4. Cost: Microwave boards cost 3-5× more due to materials and testing. We support both RF and microwave with dedicated production lines.
For 3-10 GHz (X-band to Ku-band): High-TG FR-4 or Rogers RO4350B — cost-effective with Df 0.0037. For 10-30 GHz: Rogers RO4003C (Df 0.0027) or RO3003 (Df 0.0010) — low loss for Ku/Ka-band. For 30-77 GHz: PTFE laminates (Rogers RO3003, Taconic TLY-5) with Df < 0.001 — essential for mmWave. For automotive radar: Ceramic-filled PTFE for temperature stability (±3% Dk from −40°C to +125°C). For space: Low-outgassing PTFE with ASTM E595 certification (TML < 1.0%, CVCM < 0.1%). We stock all major materials and test every lot for actual Dk/Df before production.
PIM (Passive Intermodulation) occurs when two or more signals mix in non-linear junctions (loose connectors, ferromagnetic materials, contamination), creating unwanted frequencies. In 4G/5G systems, PIM causes interference, reduced throughput, and dropped calls. Typical PIM requirements: ≤−155 dBc for standard antennas, ≤−160 dBc for high-density base stations. We achieve PIM ≤−159 dBc using: 1. RTF copper — smoother surface reduces non-linear junctions. 2. ENEPIG finish — nickel-free surface eliminates ferromagnetic losses. 3. PIM testing — 100% verification at +43 dBm (20W) per IEC 62037. We provide PIM test reports with every board.
Low-loss copper has reduced surface roughness to minimize conductor loss at high frequencies. Copper types: Standard HTE: Rz 7-11 μm — acceptable < 3 GHz. RTF (Reverse Treated Foil): Rz 3-5 μm — recommended for 3-30 GHz. VLP (Very Low Profile): Rz < 3 μm — essential for > 30 GHz. HVLP (Hyper VLP): Rz < 1.5 μm — for 77 GHz radar and mmWave. Roughness effect: At 39 GHz, HVLP copper reduces loss by 1.5 dB/inch compared to standard copper. We use RTF as standard for all RF/microwave boards, with VLP/HVLP available for > 30 GHz applications. Profilometer testing verifies roughness on every lot.
1. Material testing: 100% Dk/Df verification of every laminate lot using resonant cavity or split-post methods. 2. TDR impedance: 100% single-ended and differential impedance testing, ±7% or ±10% tolerance. 3. VNA testing: Insertion loss, return loss, VSWR, and S-parameters to 77 GHz. 4. PIM testing: IEC 62037 compliant, −158 to −162 dBc @ +43 dBm. 5. Phase matching: For phased arrays, verify phase within ±5° across channels. 6. X-Ray inspection: Verify microvias, layer registration, and ground via formation. Test reports include S-parameter files (.s2p), Smith charts, and pass/fail data.
We offer two impedance control levels: Standard production: ±10% tolerance — suitable for most RF applications up to 30 GHz. High-precision: ±7% tolerance — required for phased arrays, 5G mmWave, and > 30 GHz applications. Every board gets 100% TDR testing — no sample testing. TDR measures impedance along the entire trace length, revealing discontinuities from vias, connectors, or material variations. Typical test setup: 50Ω single-ended microstrip/stripline, 100Ω differential pairs, 1-20 GHz sweep frequency. For tight tolerance (±7%), we recommend impedance-controlled stackup design with dedicated reference planes.
Yes, hybrid stackups combine RF laminates (for microwave layers) with standard FR-4 (for digital and power layers), reducing cost by 40-60% versus all-RF construction. Typical hybrid: Outer layers: Rogers RO4350B or PTFE for RF signals (28-39 GHz). Inner layers: High-TG FR-4 for power distribution and digital control. Challenges we solve: CTE mismatch between materials — use compatible prepregs to prevent delamination. Registration — critical for microvias transitioning between materials. Bonding — specialized bonding sheets ensure reliable lamination. We’ve produced hybrid boards up to 20 layers for 5G base stations and satellite payloads. Contact us for stackup design assistance.
ENEPIG is recommended for > 30 GHz — nickel-palladium-gold eliminates ferromagnetic nickel layer, reducing insertion loss by 2+ dB compared to ENIG. OSP (Organic Solderability Preservative) provides the best RF performance (lowest loss) for antenna boards, but has 3-6 month shelf life. Immersion Silver offers good RF performance with moderate shelf life (6-9 months). ENIG is acceptable for < 10 GHz but not recommended for mmWave due to nickel losses. Hard Gold (electrolytic gold over nickel) is used for edge connectors and RF switches with repeated mating cycles. For 5G mmWave base stations and phased arrays: Use ENEPIG. For antenna arrays: Use OSP. For general RF < 10 GHz: ENIG is acceptable.